2012 Komatsu PC308USLC-3EO EXCAVATOR - RARE LARGE UP TO 2.5 YARD TRUE ZERO TAIL SWING

TRUE RARE ZERO TAIL SWING 2.5 YARD EXCAVATOR  PLUS 18 HIGH QUALITY ATTACHMENTS FOR THIS HARD TO FIND 73,000 LB EXCAVATOR  IN THIS CONDITION - NO DEF - NO SENSOR OR EMISSIONS ISSUES

NOTE: DO HAVE A NEW TAKE OFF GEITH 90 MM PIN GRABBER COUPLER  WORTH $16,000.00 THAT WE WERE GOING TO INSTALL TO GRAB LARGER BUCKETS AND MANY OF THE FOLLOWING ATTACHMENTS LISTED BELOW - JUST INSTALL IT.

IT COMES C/W NEW PINS - MACHINE OF COURSE IS PLUMBED AND CONTROLS ARE INSTALLED TO RUN IT

TAKE  THE MACHINE  WITH  BOTH THE 32 INCH AND 46 INCH BUCKET INCLUDED WHICH  WOULD HOOK UP TO THIS VARIABLE CENTER - VARIABLE 80 OR 90MM PIN GRABBER COUPLER FOR $115,000.00  OR $120,000.00 WITH THE GEITH PIN GRABBER COUPLER INCLUDED.

This machine is in excellent physical condition with its original paint -  factory decals and no dents nor body work required - all mirrors are perfect  

The cab and interior are perfect and everything functions as it should - is wired for CB radio or company radio.  

It comes from a large fleet that was liquidated due to the owner's death who worked almost exclusively for Hydro Quebec.

The machine has obviously not been a demolition or hard digging machine and with the $40K of additional lifting valves and Isogarde  hydro line swing limiter options installed and the perfect cab and how tight the machine is it appears to have been used more for a tracked excavator jobsite crane in tight locations due to the zero tail swing that allows it to operate in  a 17' 4" space and stability of the long and wide undercarriage along with the heavy counterweight .  

The machine has been fully maintained by SMS through a regular scheduled maintenance program.

It is located in Cambridge Narrows NB and will be ready to work immediately.

It does not require any additional time or maintenance before it can be put to use.

THIS REALLY IS A PERFECT MACHINE FOR  OVER $400,000.00 LESS THAN THE COST OF REPLACEMENT  AND WORKS IN CONFINED SPACES AND ON ROADWAYS AND WITH WIDE AND LONG UNDERCARRIAGE PERFECT FOR SOFT GROUND  

AND NEEDS NOTHING AND IS READY TO WORK WHEN IT ARRIVES ON SITE EXCEPT INSTALL THE NEW GEITH PIN GRABBER COUPLER - ABOUT 1-2 HOURS WORK FOR YOUR MECHANIC.  

THIS MACHINE HAS 1O HOURS ON COMPLETE SERVICE AND WAS GONE THROUGH TO MAKE IT PERFECT - READY TO WORK NOW

WE DID AN EXCAVATION FOR A NEW SHOP AS PER THE VIDEO AND THIS BURNED 15-18 LITRES PER HOUR DIGGING IN THE FROZEN SHALE ON  JANUARY 4, 20023

UNDERCARRIAGE IS 90% - NO LEAKS AND ALL PINS ARE TIGHT - MOTOR AND HYDRAULICS ARE PERFECT

TAKE THIS EXCELLENT READY TO WORK 73,000 LB MACHINE WITH AS NEW EXTREME DUTY ESCO 32 INCH TRENCHING BUCKET - THE GEITH PIN GRABBER COUPLER  AND THE 44 INCH DIGGING BUCKET FOR $120,000.00.

NEW COST TO REPLACE IS OVER $500,000.00 SO TAKE THIS MACHINE FOR 1/4 OF THAT PRICE AND HAVE WORKING NOW NOT MONTHS FROM NOW.

FINANCING AVAILABLE ****OAC***** by several leasing companies we deal with.

FRANK 604-476-7777

THIS CAN BE MOVED QUICKLY BY OUR TRUCKER - WE GET GREAT RATES.

COMPLETE 10 HOURS SINCE THE FOLLOWING SERVICE:

1) ALL OILS AND FILTERS CHANGED INCLUDING FINAL DRIVES

2) 2 NEW HD BATTERIES AND BATTERY CUT-OFF SWITCH INSTALLED

3) TRACKS TENSIONS ADJUSTED

4) GO OVER MACHINE FOR ANY ISSUES AND REPAIRED

5) REMOVED THE 80MM HYDRAULIC  PIN GRABBER COUPLER AND PUT ON AS NEW ESCO HARD SURFACED AND BUILT FOR PC308 KOMATSU 34 INCH EXTREME DUTY TRENCHING BUCKET WITH AS NEW PINS - NO WEAR IN STICK OR H LINK BUSHINGS AND BUCKET IS TIGHT

MACHINE ALSO COMES WITH THE ORIGINAL 44 INCH 5 TOOTH BUCKET SEEN IN THE PICTURES - BUT IT DOES REQUIRE A DAYS WORTH OF WORK PLATING AND HARD SURFACING TO MAKE PERFECT AND AS NEW (about $1000.00 worth of work - Original Teeth and Shanks are good - with new side wear bars - but has minor cracking around teeth area)  COMES WITH THE PINS FOR THE PIN GRABBER TO GRAB  

WE ALSO HAVE SITTING THERE AVAILABLE FOR PURCHASE WITH THE MACHINE OR SOLD SEPARATELY:  (SEE MY OTHER AD FOR THESE ATTACHMENTS)

1) OTHER BUCKETS INCLUDING A NEW X HAND 60 INCH 6 IN 1 CLEANUP - GRAPPLE - SCREENING BUCKET WORTH $60,000.00 TAKE IT FOR $25,000.00

2) A MB BF90 CONCRETE AND ROCK CRUSHER BUCKET C/W CORRECT TOP PLATE MOUNT FOR THIS MACHINE WORTH $90,000.00 NEW TAKE IT FOR $35.000.00

3) AS NEW SLASHBUSTER STUMP GRINDER C/W CORRECT TOP PLATE FOR THIS  WORTH  $60,000.00 USD (81,500.00 CDN) WITH A 1 YEAR WAIT FROM SLASHBUSTER - TAKE IT FOR $40,000.00

4) PROMAC Model RGP  52 INCH BRUSH CUTTER   TREE CUTTER UP TO 6 INCHES  - GRINDS AND MULCHES BRUSH - BLUEBERRIES PLANTS  - TAKE IT FOR $15,000.00

5)  LANDHERO NEW 67 INCH BRUSH RAKE FOR 200-300 CLASS EXCAVATORS -  90 MM FRONT PINT 80 MM REAR PIN - TAKE IT FOR $6000.00

6) AS NEW TEREX LARGE 160 HP DUAL DRUM ROCK AND CONCRETE GRINDER LOW HOUR READY TO WORK $125,000.00 GRINDER WITH 90MM FRONT PINT 80 MM REAR PIN TAKE IT FOR $40,000.00

7) STANLEY 200-380 CLASS HS2000 20000 FT LB PLATE COMPACTOR/DRIVER 80 OR 90 MM PINS WITH 15 INCHES BETWEEN EARS - $20,000.00 + PLATE COMPACTOR TAKE IT  FOR $8000.00

8) ESCO 48 INCH 2.5 YARD DIGGING BUCKET C/W 90 MM PINS AND WELDED CUTTING EDGE ON TEETH - AS NEW EXTREME DUTY 90 MM PINS AS NEW COST $15,0000.00 USD - TAKE IT FOR $8000.00

9) AS NEW FELCO COMPACTOR BUCKET ALL IN ONE UNIT - STOP CHANGING BASK AND FORTH TO DO BACKFILLING IN TRENCHES ETC NEW COST $36,000.00 - TAKE IT FOR $15,000.00 - NOTE SITTING IN OUR LANGLEY BC YARD (sold)

10) 85K NEW KISHOFFER 20,000 LB CAPACITY DEMOLITION - LOGGING  3 YARD C/W PIN GRABBER MOUNT TOP FIT RIGHT ON THIS MACHINE NEW COST $85,000.00 - TAKE IT FOR $45.000.00  - NOTE SITTING IN OUR LANGLEY BC YARD

11) NEW HENSLEY ADCO 30 INCH RIPPING V BUCKET  MAKES SHORT WORK OF FROZEN OR HARD SANDSTONE OR SHALE ETC - NEW COST $15,000.00 USD  - TAKE IT FOR $8,000.00

12) MP MACFREY - SONS AMERICAN BUILT ALL AR400 STEEL 2.5 YARD DITCHING - TRENCHING V BUCKET  C/W NEW 90 MM PINS SET UP FOR THIS MACHINE NEW COST $15,000.00 USD TAKE IT FOR $8,000.00

13) ALLU PM200 ROTARY DRUM SOILS-SLUDGE-COMPOST MIXING 200-350 CLASS WITH  CEMENT SLURRY INJECTED INTO THE PROTECTED SPRAY HOSE -  SET UP WITH 90 MM PINS FOR THIS MACHINE - NEW  COST $100,000.00

TAKE THIS AS NEW UNIT FOR $30,000.00

14)  2020 OKADA 7500 FT LB  HYDRAULIC BREAKERS/HAMMERS  FRESH 0 HOUR OKADA FACTORY $35,000.00 STAGE  II REBUILD WITH NEW PISTON ALL  NEW BUSHING - SEALS  NEW MOIL POINT AND 1 AS NEW SPARE MOIL POINT

TAKE THIS $100,000.00 HAMMER FOR $60,000.00  WITH 6 MONTHS WARRANTY FROM OKADA

15)NEW OKADA CUT 8O FR COMBINATION CONCRETE - REBAR - STEEL BEAM SHEAR C/W 80MM PINS FOR THIS MACHINE - NEW COST $80,000.00 - TAKE IT FOR $35,000.00 - NOTE SITTING IN OUR LANGLEY BC YARD

16) CP 24 INCH EXTREME DUTY 4 SHANK STAGGERED LONG RIPPERS BUCKET C/W 3 NEW TIGER TEETH AND ALL NEW RIPPER TEETH - $15,000.00 CUSTOM BUILT WITH 16 WEEKS LEAD TIME - TAKE IT FOR $8,000.00

17)AS NEW HYDRAULIC FLOW COMBINER VALVE TO TAKE VOLUMES FROM TWO PUMPS WITH FOOT PEDAL ON-OFF SWITCH OR CONTROL PANEL FULL TIME SWITCH - THIS IS FOR RUNNING ATTACHMENTS THAT REQUIRE HIGHER FLOW VOLUMES LIKE GRINDERS - BRUSH CUTTER - CRUSHER BUCKET - HYDRAULIC HAMMERS ETC THIS IS AT OUR  YARD LANGLEY BC

BUT LEAVES YOUR MAIN FUNCTIONS RUNNING SO TO MAKE MACHINE SMOOTH AND RESPONSIVE TAKE THIS VALVE FOR $3000.00

18) SET OF KOMATSU FACTORY AUXILIARY  PIPING PLUS SET OF PIPING FOR CASE DRAIN LINE  FOR ATTACHMENTS - THESE ARE AT OUR YARD LANGLEY BC

IF YOU PURCHASE MACHINE WILL INCLUDE THE LINES AND HOSES FREE - JUST PAY THE TRUCKING

The machine being offered is a Komatsu PC308USLC Hydraulic Excavator. It is designed with a short tail swing profile, specifically for working in congested or confined areas. This reduces the risk of safety issues that conventional excavators might pose. It is perfect for projects on roadways, bridges, urban areas, or any location with limited space. The PC308USLC provides the expected performance and productivity of Komatsu equipment.

THIS MACHINE HAS $35,000.00 - $40,000.00 OF THE FOLLOWING OPTION INSTALLED:

1) ISOGARD COMPUTER SWING LIMITER TO STOP MACHINE SWINGING INTO POWER LINES OR OTHER OBSTACLES

To help operators of cranes and excavators work safely next to power lines or other obstacles.

Model 610 for excavators can be programmed to limit in many combinations of angle and swing. The programming is done in a very simple 2-step procedure.

Includes

Keyboard

Inclinometer

Swing detector

2) LIFTING VALVES - SO LEGALLY CAN BE USED AS A CRANE - BOOM AND STICK WILL NOT CREEP OR LOWER UPON HOSE FAILURES

Burst protection is to be fitted on all earthmoving equipment used as a crane, where the rated capacity exceeds 1 tonne. The burst protection is to be fitted to both the boom and dipper arm of the equipment. Burst protection is to comply with the performance requirements of ISO 8643: Earthmoving machinery – Hydraulic excavator and backhoe loader boom-lowering control device – Requirements and tests as per WorkSafe.

Copy and paste the Komatsu PC308USLC PDF feature sheet:

https://www.mediafire.com/file_premium/2epvsismwtfnxl1/KOMATSU-PC308USLC-FACTORY-BROCHURE.pdf/file

Some key features of the Komatsu PC308USLC include:

Small occupied width: The machine occupies a width of 5325 mm (17'5") or less, allowing it to work efficiently in confined areas. The tail swing protrudes only 1.5" from the tracks.

High stability: It offers exceptional lifting capacity and stability, thanks to its large counterweight that requires no additional clearance.

Larger cab: The Komatsu PC308USLC has a spacious cab with a low-noise design and viscous cab mounting. The sliding convex door makes it easy to enter confined areas and reduces the risk of damage when open on roadways.

Standard features of the machine include effortless joystick controls, a large seat, cup holder, sliding window, internal storage with a hot and cold box, and auto air conditioning.

Here are the specifications of the Komatsu PC308USLC:

Manufacturer: Komatsu

Model: PC308USLC-3

Year: 2012

Serial No.: KMTPC160E02030289

SMS Stock Number: R33792

Meter Reading: 10,715 hours

Additional details:

Drive train: 3 speeds

Track width shoes: 28 - 33.5 inches (700 - 850 mm)

Track length: 16 ft. 3 in. (4,955 mm)

Engine specifications:

Engine Type: 4-cycle, direct driven

Engine Make: Komatsu

Engine Model: SAA6D107E-1

Fuel Type: Diesel

Cylinders: 6

Gross Horsepower: 200 hp (149 kW) @ 2,050 rpm

Net Horsepower: 187 hp (140 kW) @ 2,050 rpm

Cooling: Water-cooled

Displacement: 408 cu. in. (6.69 l)

Rated Speed: High: 2.9 mph (4.6 km/h), Mid: 2.1 mph (3.4 km/h), Low: 1.8 mph (2.9 km/h)

Komatsu PC308USLC-3 Excavator

CATEGORY: EXCAVATORS

MANUFACTURER: KOMATSU

MODEL: PC308USLC-3

Boom/Stick Excavator Option 1

Max Cutting Height 33.3 ft (10 m)

Max Digging Depth 21.2 ft (6 m)

Max Loading Height 23.6 ft (7 m)

Max Reach Along Ground 34.3 ft (10 m)

Max Vertical Wall Digging Depth 19.5 ft (6 m)

Shipping Length of Unit 31.4 ft (9 m)

Boom/Stick Excavator Option 2

Max Cutting Height 33.3 ft (10 m)

Max Digging Depth 22.8 ft (7 m)

Max Loading Height 23.6 ft (7 m)

Max Reach Along Ground 34.3 ft (10 m)

Max Vertical Wall Digging Depth 19.5 ft (6 m)

Shipping Length of Unit 31.4 ft (9 m)

Boom/Stick Excavator Option 3

Max Cutting Height 35.2 ft (11 m)

Max Digging Depth 24.9 ft (7 m)

Max Loading Height 26.2 ft (8 m)

Max Reach Along Ground 36.7 ft (11 m)

Max Vertical Wall Digging Depth 22.7 ft (7 m)

Shipping Length of Unit 31.2 ft (9 m)

Bucket

Maximum Bucket Capacity 2.5 cu yd (2 m)

Minimum Bucket Capacity 0.9 cu yd (0 m)

Reference Bucket Capacity 1.6 cu yd (1 m)

Dimensions

Ground Clearance 1.7 ft (0 m)

Height - Top of Cab 10.3 ft (3 m)

Length of Track on Ground 13.3 ft (4 m)

Removal Counterweight Clearance 4 ft (1 m)

Tail Swing Radius 11.4 ft (3 m)

Width to Outside of Tracks 11.4 ft (3 m)

Engine

Aspiration Turbocharged and air to air after cooled

Displacement 408 cu in (0 m)

Engine Model SAA6D107E-1

Gross Power 200 hp (149 kw)

Net Power 187 hp (139 kw)

Operating Specifications

Cooling System Fluid Capacity 5.5 gal (19 l)

Engine Oil Capacity 6.1 gal (23 l)

Fuel Capacity 103 gal (390 l)

Hydraulic System Fluid Capacity 55.5 gal (208 l)

Operating Weight 71938 lbs (32,631 kg)

Swing Drive Fluid Capacity 2.2 gal (8 l)

Swing Mechanism

Swing Speed 9.5 rpm

Undercarriage

Draw bar Pull 59180 lbs (26,844 kg)

Max Travel Speed 2.9 mph (3 kph)

Number of Carrier Rollers per Side 2

Number of Shoes per Side 48

Number of Track Rollers per Side 8

Additional Details

THIS REALLY IS A PERFECT MACHINE FOR $400,000.00 LESS THAN COST OF REPLACEMENT  AND WORKS IN CONFINED SPACES AND ON ROADWAYS AND WITH WIDE AND LONG UNDERCARRIAGE PERFECT FOR SOFT GROUND  

AND NEEDS NOTHING AND IS READY TO WORK WHEN IT ARRIVES ON SITE EXCEPT INSTALL THE NEW GEITH PIN GRABBER COUPLER - ABOUT 1-2 HOURS WORK FOR YOUR MECHANIC.  

PLEASE CALL OR TEXT FRANK 604-476-7777

Copy and paste the Komatsu PC308USLC PDF feature sheet:

https://www.mediafire.com/file_premium/2epvsismwtfnxl1/KOMATSU-PC308USLC-FACTORY-BROCHURE.pdf/file

Some key features of the Komatsu PC308USLC include:

• Small occupied width: The machine occupies a width of 5325 mm (17'5") or less, allowing it to work efficiently in confined areas. The tail swing protrudes only 1.5" from the tracks.
• High stability: It offers exceptional lifting capacity and stability, thanks to its large counterweight that requires no additional clearance.
• Larger cab: The Komatsu PC308USLC has a spacious cab with a low-noise design and viscous cab mounting. The sliding convex door makes it easy to enter confined areas and reduces the risk of damage when open on roadways.

Standard features of the machine include effortless joystick controls, a large seat, cup holder, sliding window, internal storage with a hot and cold box, and auto air conditioning.

Here are the specifications of the Komatsu PC308USLC:

• Manufacturer: Komatsu
• Model: PC308USLC-3
• Year: 2012
• Serial No.: KMTPC160E02030289
• SMS Stock Number: R33792
• Meter Reading: 10,715 hours

Additional details:

• Drivetrain: 3 speeds
• Track width shoes: 28 - 33.5 inches (700 - 850 mm)
• Track length: 16 ft. 3 in. (4,955 mm)

Engine specifications:

• Engine Type: 4-cycle, direct driven
• Engine Make: Komatsu
• Engine Model: SAA6D107E-1
• Fuel Type: Diesel
• Cylinders: 6
• Gross Horsepower: 200 hp (149 kW) @ 2,050 rpm
• Net Horsepower: 187 hp (140 kW) @ 2,050 rpm
• Cooling: Water-cooled
• Displacement: 408 cu. in. (6.69 l)
• Rated Speed: High: 2.9 mph (4.6 km/h), Mid: 2.1 mph (3.4 km/h), Low: 1.8 mph (2.9 km/h)

Komatsu PC308USLC-3 Excavator

• CATEGORY:  EXCAVATORS
• MANUFACTURER:  KOMATSU
• MODEL:  PC308USLC-3

Boom/Stick Excavator Option 1

Boom/Stick Excavator Option 2

Boom/Stick Excavator Option 3

Bucket

Dimensions

Engine

Operating Specifications

Swing Mechanism

Undercarriage