ONE OF A KIND CUSTOM BUILT $1.3 MILLION LONG REACH EXCAVATOR - SHEET PILE DRIVING - DEMOLITION - EXCAVATING

ONLY MACHINE LIKE IT IN NORTH AMERICA TOOK 2 YEARS TO PUT TOGETHER TOTALLY REBUILT MACHINE FINISHED IN 2023 LOOKS AND OPERATES AS NEW WITH NO EMMISIONS ISSUES

NOR DEF - SENSOR ISSUES  

ONE OF A KIND CUSTOM BUILT EXCAVATOR FOR DIVERSE APPLICATIONS – TAKE THIS $1.300,000.00 REPLACEMENT MACHINE WITH 1 BUCKET FOR $400,000  

OR WITH NEW 2021 $200,000.00 PLUS 175 HYDRAULIC HORSEPOWER HYDRARAM SHEET PILE DRIVER TO DRIVE SHEET PILES - H PILES ETC for $500,000

CUSTOM 60-FOOT REACH 3-PIECE BOOM FOR SHEET PILE DRIVING - LARGE 12000 FT LB HAMMERS WORKING AT 65 PLUS FEET - LARGE DEMOLITION PROCESSORS - GRAPPLES - BUCKETS - LARGE DUAL DRUM GRINDERS ETC

LOW-HOUR MINT CONDITION MACHINE WITH NEW KOMATSU CUSTOM 60 FOOT EXTREME DUTY 3 SECTION BOOM - BOOM ALONE IS WORTH OVER $300,000.00 WITH THE COST OF INSTALLATION

CAN DRIVE 40-50-60 FOOT SHEETS PILE REPLACES LARGE CRANE MOUNTED UNITS WITH POWERPAK HYDRAULIC UNITS AND REDUCES YOUR CREW FROM A 4 OR 5 MAN CREW TO 2 AND WILL DRIVE 4 TIMES AS MANY SHEETS PER HOUR PLUS READY TO DRIVE PILES 1/2 HOUR AFTER ARRIVING ON-SITE NOT A DAY LIKE CRANES AND WILL WORK IN TIGHT LOCATION AND SWAMP GROUND JUST USING WOOD PADS IF REQUIRED

MACHINE THEN CAN BE USED ON THE JOB FOR ALL EXCAVATOR WORK REQUIRED - THEN REMOVE THE SHEET PILES WHEN THE EXCAVATION IS DONE - NO SECOND MACHINE REQUIRED - THIS MACHINE WAS PUT TOGETHER FOR A LARGE JOB IN SWAMPY GROUND FOR BUILDING A BRIDGE WHERE THERE WERE 40 FOUNDATIONS THAT WERE 30 FEET WIDE X 50 LONG THAT AFTER DRVING THE SHEETS NEEDED TO BE EXCAVATED TO A DEPTH OF 20 FEET - BUT DUE TO COVID THAT JOB WAS PUT AND REMAINS ON HOLD.

THIS IS NOT A SPAGETTI BOOM  LONG REACH - USE LARGE 12000 ft lb HYDRAULIC HAMMERS - 10,000 LB HYDRAULIC DEMOLITION PROCESSORS - GRAPPLES - HYDRAULIC DUAL DRUM GRINDERS - PLATE COMPACTORS - DIG WITH VARIOUS BUCKETS UP TO 4 YARDS ALL WITH ONE MACHINE

THE MACHINE HAS THE FOLLOWING:

CUSTOM MODIFIED NEW FACTORY ALL KOMATSU 3-PIECE BOOM C/W NEW KOMASTSU LOG LOADER HD CYLINDERS TO GET THE REQUIRED REACH AND HEIGHT CONFIGURATION NOT POSSIBLE WITH A REGULAR EXCAVATOR BOOM:

ALL-NEW CUSTOM HYDRAULIC STEEL LINES - VALVES - FOR 3 HYDRAULIC FUNCTIONS PLUS CASE DRAIN

NEW HIGH END PROFESSIONALLY INSTALLED GERMAN AUTO GREASER SYSTEM

AS NEW GEITH HYDRAULIC PIN GRABBER COUPLER - CHANGE ATTACHMENTS IN MINUTES FROM THE SEAT

HYDRAULIC REMOVEABLE KOMATSU DEMOLITION COUNTERWEIGHT  ($50,000.00 Factory Option) PLUS $35,000.00 IN ADDITIONAL CUSTOM REAR TOP MOUNTED WEIGHTS  THAT IS DESIGNED TO GO AROUND THE FACTORY HYDRAULIC DROP SYSTEM - KEEPS REAR SWING CLEARANCE TO FACTORY SPECS OF 1.320 METERS OR 52 INCHES SO AS TO SWING OVER SHEET PILES WITH A 42 INCH WCB REQUIRED ABOVE GROUND HEIGHT WHILE DOING THE EXCAVATION SWINGING OVER  THE SHEET PILES

CUSTOM HYDRAULICS FOR 3 AUXILIARY HYDRAULIC CIRCUITS PLUS CASE DRAIN LINE TO RUN ANY DEMOLITION OR SHEET PILE ATTACHMENT

CAN BE MOVED COMPLETE ON 8 or 9 AXLE LOW BED AT HEIGHT OF 14 FEET ON THE BED

TO GET THE REQUIRED REACH AND HEIGHT CONFIGURATION NOT POSSIBLE WITH A REGULAR EXCAVATOR BOOM:

CHARLIE SMITH MACHINE REMOVED THE EXISTING EXCAVATOR BOOM AND INSTALLED A BRAND NEW KOMATSU LOG LOADER BOOM C/W NEW HYDRAULIC CYLINDERS - REMOVED THE GRAPPLE AND CUSTOM INSTALLED THE ORIGINAL STICK -  REBUSHED  THE ENTIRE STICK COMPLETELY REBUILT BOTH BUCKET - STICK CYLINDERS - REBUILT THE GEITH HYDRAULIC PIN GRABBER COUPLER

DC WELDING LANGLEY INSTALLED ADDITIONAL CUSTOM QUICK DETACH COUNTERWEIGHT'S  THAT FIT BEHIND AND CAN BE REMOVED WITH THE FACTORY HYDRAULIC DROP COUNTERWEIGHT A COST OF OVER $35,000.00

MACHINE HAS  0 WORKING HOURS ON NEW FACTORY KOMATSU HYDRAULIC PUMPS INSTALLED

SMS KOMATSU SURREY WENT THROUGH AND REBUILT THE COMPLETE HYDRAULIC SYSTEM INCLUDING THE MAIN VALVE BODY TO INSTALL THE ADDITIONAL HYDRAULIC VALVES AND SET UP TO RUN THE NEW HYDRARAM SHEET PILE DRIVER OR ANY DEMOLTION ATTACHMENTS FOR A COST OF OVER $75,000.00

NAHANNI TRUCK AND TRAILER  BLASTED THE UNDERCARRIAGE AND ALL GUARDING WAS REMOVED AND BLASTED AND MAIN BODY WAS HAND SANDED THEN COMPLETELY  PAINTED WITH QUALITY EPOXY  PAINT AND NEW KOMATSU DECALS  INSTALLED  ON THE MACHINE

THE FOLLOWING EQUIPMENT IS AVAILAVAILABLE AND  READY TO WORK ON THIS MACHINE: (Copy and Paste Ad Urls)

a)   NEW $220,000.00 2021 HYDRARAM 175 HYD HP SHEET PILE DRIVER 45-65 TON CLASS  TAKE FOR $100,000.00 (with machine only)

https://www.kijiji.ca/v-view-details.html?adId=1631390586

b)   LOW HOUR $125,000.00 TEREX WS-120MD 160 HYD HP DUAL DRUM GRINDER 30-50 TON EXCAVATOR TAKE FOR $40,000.00

https://www.kijiji.ca/v-view-details.html?adId=1539702132

c)  NEW $85,000.00 KINSHOFFER LOG LOADER -  3 3 YARD DEMOLITION 360 DEGREE ROTATION 20K CAPACITY GRAPPLE TAKE FOR  $40,000.00  

https://www.kijiji.ca/v-view-details.html?adId=1630113607&siteLocale=en_CA

d)  OKADA FACTORY REBUILT 0 HOUR 2020 $110,000.00 HYDRAULIC HAMMER/BREAKER C/W TWO NEW MOIL POINTS TAKE FOR $60,000.00

https://www.kijiji.ca/v-view-details.html?adId=1632550369

e)   3 X HENSLEY HPX 400-490 KOMATSU 30-46-70 IN HD BUCKETS ALL AS NEW OR NEW  - TAKE ALL THREE FOR $25,000.00

https://www.kijiji.ca/v-view-details.html?adId=1632754851

f)   NEW 2023 PRIMARY DEMOLITION PROCESSOR & 2023 DEMOLITION SORTING GRAPPLE - TAKE BOTH WITH MACHINE $50,000

https://www.kijiji.ca/v-view-details.html?adId=1633069312

g)  AS NEW $80,000.00  OKADA CUT 80FR STEEL - CONCRETE DEMOLITION SHEAR - TAKE FOR $35,000.00

https://www.kijiji.ca/v-view-details.html?adId=1527158230

h) ESCO 400 - 450CLASS HEAVY DUTY 24 INCH BUCKET C/W EXTREME DUTY RIPPER SHANK HOLDER -  FOR RIPPING HARD GROUND AND CLEANING BETWEEN PILES IN FOUNDATION  TAKE IT FOR $6000.00

ALL OF WHICH ARE AVAILABLE FOR THIS MACHINE TO WORK NOW - SEE MY OTHER ADS.

MACHINE COST TO REPLACE WELL OVER 1.3 MILLION AND WITH TODAY'S ISSUES MORE THAN 6 - 12 MONTHS OF PARTS AND WORK. TO BUILD

NOTE: THE APPRAISAL OF THE MACHINE SHOWN WAS DONE BEFORE MACHINE WAS FINISHED AND BEFORE I SPENT ANOTHER $300,000.00 PLUS ON  COMPLETION  - MACHINE IS CLEAR TITLE - READY TO WORK - NEEDS NOTHING

SEE COMPLETE DETAILS AND 130 PICTURES OF THIS MACHINE HERE: (CLICK or copy and paste web link)

https://www.mediafire.com/folder/5j7f20t4zrld4/K%20OMATSU-PC450LC-8

Excavator Details

This unique excavator is a game-changer, designed to handle a range of tasks with precision.

A comprehensive rebuild was executed, sparing no expense, resulting in a fully enhanced machine finished in 2023.

Note: Replacement Cost Well over  $1,300,000  without the HydraRam Sheet Pile Driver or other attachments

Features:

Excavator Hours: 7,300 (Total Rebuild in 2023)

Custom All Komatsu 3-Piece Boom for Multiple Versatile Attachments

Enhanced for Sheet Pile Driving, Excavation, Demolition, and More

Comes with New 2021 175 Hydraulic HP HydraRam Sheet Pile Driver (Value: $250,000) for $500,000

Our Total Investment: Over $600,000 or $800,000 with HydraRam Sheet Pile Driver

As New Hensley 46-Inch Extreme-Duty Digging Bucket Included

Capabilities:

Excavating To 34-36 Feet Depth with Included 46 Inch 2.5 Yard Bucket - 70 Inch 4 Yard  Bucket Available (Both are Hensley Extreme Duty)

Sheet Pile Driving

Large Hydraulic Hammers and Demolition Processors  Hydraulic Grapples - Demolition (Vertical and Horizontal Reach: 60-70 Feet Depending on Attachment)

Large Dual Drum Grinder

Additional Equipment Available:

Kishoffer T40HPX – 114 Helix Drive Grapple with 20,000 lb 2.5 Yard Capacity  (Value: $85,000)

Choice of Several Buckets

Okada Cut82 Rotating Demolition Shear

2020 - 0 Hours Since Factory Rebuilt Okada Model: ORV7500 7500 ft lb hammer  Serial Number: 363B538 Dimensions: 124" L Operating Weight: 5,950 lbs

…and much more!

Why Choose This Excavator:

Handles Various Attachments with Ease

Custom 3-Piece Boom for Precise Operations

Rebuilt and Enhanced for Exceptional Performance

Can Replace Cranes for Sheet Pile Work in Tight Locations

Versatile and Productive Addition to Any Fleet

Will Look At 35-40 Foot  Newer Class A Diesel Pusher Motorhome  Or A  1964 - 1971 Classic Muscle Car  As Part Trade

Financing Available OAC

Contact Frank: 604-476-7777

Location: Langley BC

NOTE: The Appraisal Shown in image #6 does not take into account the cost of the New $150,000.00 Factory Komatsu Log Loader Boom c/w pins and cylinders  or the $200,000.00 plus spent after this viewing to complete the machine to its current finished state.

Will take a Class A Newer Diesel Pusher Motorhome - Classic 64-71 Muscle Car as part trade.

Note: Due to health reasons from the smog in the Fraser Valley, after 53 years in the demolition and rock excavation business we’re retiring and relocating to NB, which is why we’re selling this exceptional piece of equipment.